Name: SG510 Series

Text: Blue Coat® Systems
SG510 Series

Installation Guide

Version: SGOS 4.2.x and 5.1.x

Contact Information
Blue Coat Systems Inc.
420 North Mary Ave
Sunnyvale, CA 94085-4121
http://www.bluecoat.com/support/index.html
bcs.info@bluecoat.com
support@bluecoat.com
http://www.bluecoat.com
For concerns or feedback about the documentation: documentation@bluecoat.com
Copyright© 1999-2007 Blue Coat Systems, Inc. All rights reserved worldwide. No part of this
document may be reproduced by any means nor modified, decompiled, disassembled, published or
distributed, in whole or in part, or translated to any electronic medium or other means without the
written consent of Blue Coat Systems, Inc. All right, title and interest in and to the Software and
documentation are and shall remain the exclusive property of Blue Coat Systems, Inc. and its licensors.
ProxySG™, ProxyAV™, CacheOS™, SGOS™, Spyware Interceptor™, Scope™, RA Connector™, RA
Manager™, Remote Access™ are trademarks of Blue Coat Systems, Inc. and CacheFlow®, Blue Coat®,
Accelerating The Internet®, WinProxy®, AccessNow®, Ositis®, Powering Internet Management®,
The Ultimate Internet Sharing Solution®, Permeo®, Permeo Technologies, Inc.®, and the Permeo logo
are registered trademarks of Blue Coat Systems, Inc. All other trademarks contained in this document
and in the Software are the property of their respective owners.
BLUE COAT SYSTEMS, INC. DISCLAIMS ALL WARRANTIES, CONDITIONS OR OTHER TERMS,
EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, ON SOFTWARE AND DOCUMENTATION
FURNISHED HEREUNDER INCLUDING WITHOUT LIMITATION THE WARRANTIES OF
DESIGN, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL BLUE COAT SYSTEMS, INC., ITS SUPPLIERS OR
ITS LICENSORS BE LIABLE FOR ANY DAMAGES, WHETHER ARISING IN TORT, CONTRACT OR
ANY OTHER LEGAL THEORY EVEN IF BLUE COAT SYSTEMS, INC. HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
Document Number: 231-02833
Document Revision: A.0 July 2006

P/N 231-02833

Blue Coat SG510 Installation Guide

page ii

Contents

Chapter 1: Unpack and Rack a Blue Coat SG510
Unpacking a SG510................................................................................................... 8
SG510 Front Panel Features..................................................................................... 8
SG510 Back Panel Features ...................................................................................... 9
Mounting the SG510 in an Equipment Rack....................................................... 10
Rack-Mounting Notes ......................................................................................... 10
Attaching the Cable Management Support......................................................... 11
Installing the Disk Drives ...................................................................................... 12
Connecting the Cables............................................................................................ 16
Powering On the SG510 ......................................................................................... 16
Power LED ............................................................................................................ 16
Chapter 2: Configure a SG510
Overview of First-Time Configuration ................................................................ 19
Section A: Configuring the SG510 with the Front Panel Features
LCD Behavior .......................................................................................................... 21
System LCD and Modes......................................................................................... 22
SG510 Control Buttons ........................................................................................... 24
Using the Front Panel to Configure Basic Network Settings............................ 25
Section B: Placing the SG510 into the Network
Section C: Initial Configuration with a Web Browser
Requirements........................................................................................................... 29
Where to go next ..................................................................................................... 30
Section D: Initial Configuration Using a Direct Serial Port Connection
Section E: Configuring the SG510 from a Remote Location

P/N 231-02833

Blue Coat SG510 Installation Guide

page iii

Step One—Enter the Remote Configuration Parameters Using a Web
Browser ............................................................................ 55
Step Two—Complete the Configuration .......................................................... 59
Section F: Logging on to the SG510
Logging on to the SG510 Management Console ............................................. 62
Logging on to the SG510 CLI ............................................................................. 64
Section G: Configuring a Front-Panel PIN
Section H: Configuring the Front-Panel LCD Behavior
Chapter 3: Removing and Installing Disk Drives
Removing a Disk Drive .......................................................................................... 72
Installing a New Disk Drive .................................................................................. 73
Chapter 4: Option Cards
Dual Gigabit Ethernet 1000B-SX (optical) Card............................................... 75
Dual Gigabit Ethernet (copper) Pass-Through Card ...................................... 75
SSL Accelerator Card........................................................................................... 75
Chapter 5: Troubleshooting
The SG510 does not power up .............................................................................. 77
The Initial Configuration Page is Not Accessible............................................... 78
Creating A Static Route to the SG510................................................................... 79
You cannot access the serial console .................................................................... 79
You cannot access the Management Console ..................................................... 79
A Security Warning Appears for the Initial Configuration Web Page ........... 80
The SG510 certificate is no longer valid .............................................................. 80
Resetting the SG510 to Factory Defaults.............................................................. 81
The SG510 Does Not Come Back Up After Rebooting ...................................... 83
Appendix A: Specifications
General Specifications ............................................................................................ 85

P/N 231-02833

Blue Coat SG510 Installation Guide

page iv

Environmental Specifications................................................................................ 86
Appendix B: Regulatory Statements
General System Cautions....................................................................................... 87
Power Cord Cautions ............................................................................................. 87
Class A Digital Warning ........................................................................................ 88
Advertencia Digital Clase A.................................................................................. 88
EC Community EMC Warning ............................................................................. 88
Advertencia EMC de la Comunidad EC ............................................................. 88
Canadian EC EMC Warning ................................................................................. 88
Australia/New Zealand EC EMC Warning........................................................ 89
Taiwan BSMI Notification ..................................................................................... 89
Japan VCCI EMC Notification .............................................................................. 89
Battery Warning Notification................................................................................ 89
Chinese Battery Warning Notification................................................................. 90
China CCC Notification ......................................................................................... 90
Lasers ........................................................................................................................ 90
Declaration of Conformity..................................................................................... 94
Appendix C: Apéndice C: Declaraciones Regulatorias
Precauciones generales del sistema...................................................................... 95
Conexión del cable de alimentación..................................................................... 95
Lasers ........................................................................................................................ 96
Appendix D: Anhang D: Regulierende Anweisungen
Allgemeine Systemvorsichtsmassnahmen .......................................................... 97
Anschliessen des Stromkabels .............................................................................. 97
Lasers ........................................................................................................................ 98
Appendix E: Simplified Chinese Regulatory Statements
P/N 231-02833

Blue Coat SG510 Installation Guide

page v

Appendix F: Traditional Chinese Regulatory Statements
Index

P/N 231-02833

Blue Coat SG510 Installation Guide

page vi

Chapter 1: Unpack and Rack a Blue Coat SG510
This installation guide provides general instructions for installing, configuring, and
using the Blue Coat SG510.
This chapter explains how to unpack the SG510, install it in an equipment rack,
insert the disk drives, connect the cables, and power it on.
After you have completed the first-time configuration of the SG510 and have
logged in, you should do the following:


Upgrade the SG510 software by downloading the latest patch release
(available at http://download.bluecoat.com).



Fully configure the appliance.
To configure the SG510, you will need to download the Blue Coat ProxySG
Configuration and Management Guide Suite, (the CMG) available on the Blue
Coat Web site at www.bluecoat.com. (Look for WebPower Login under
Support.)
You can also find tech briefs (technical briefs) on the Blue Coat Web site.

If you log on to the SG510 using a Web browser, you can access the online help by
clicking the Help button on the Management Console screens. The Management
Console is the graphical user interface for the SG510.
See “Logging on to the SG510” on page 62 for more information.

Important: Follow all warnings and instructions marked on the product and
included in this manual.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 7

Unpacking a SG510
When you receive and unpack the SG510, verify that the package contains the
following items:





Blue Coat SG510 Series Appliance
Quick Start Guide
Null-modem serial cable
License, Warranty, and Safety
information

• AC Power cord
• Disk drives (up to two)
• Cable Management Support

SG510 Front Panel Features
The figure below shows the front of a SG510.
Power, Disk
Drive, and LAN
LEDs

Front
panel

LCD
Plates that attach
to the front of the
equipment rack

Control
buttons

Figure 1-1: The Front of a SG510

The SG510 front panel has the following features:


An LCD and six control buttons to monitor activity and configure basic
networking settings.



Power, Disk Drive, and LAN LEDs.



A front panel that pivots downward and pulls outward giving you access to
up to two disk drives.



Mounting brackets that extend from each end of the chassis to secure a SG510
to an equipment rack.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 8

You can mount a SG510 in a standard mounting rack. See “Mounting the SG510 in
an Equipment Rack” on page 10 for rack mounting instructions.

SG510 Back Panel Features
The figure below shows the back of a SG510.
AC Power
Connector

Expansion Slot for
SSL or Bridge Card

USB
Ports

Serial
Port

Ethernet
Adapter
Ports

Figure 1-2: The Back of a SG510

The following features are located on the back of the SG510:


An AC power connector.



Two USB (Universal Serial Bus) ports.



A serial port to connect to a PC, to a serial terminal, or to a stand-alone serial
console terminal.



Two full-duplex, auto-sensing Ethernet network adapter ports supporting
10/100/1000 Base-T connections.



An expansion slot for optional network, bridging, or SSL cards. See Chapter 4:
’Option Cards" for more information about SG510 option cards.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 9

Mounting the SG510 in an Equipment Rack
The Blue Coat SG510 is designed to fit into a standard telco-style or four-post
cabinet style equipment rack.
The SG510 ships with the rack-mounting ears installed.

Rack-Mounting Notes
Read these notes before rack-mounting the SG510.


Elevated Operating Temperature—If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than the ambient room temperature. Therefore, consideration should
be given to installing the equipment in an environment compatible with the
maximum ambient temperature specified by the manufacturer.



Reduced Air Flow—Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is not
compromised.



Mechanical Loading—Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical loading.



Circuit Overloading—Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when
addressing this concern.



Earthing (Grounding)—Reliable earthing of rack-mounted equipment should
be maintained. Particular attention should be given to supply connections
other than direct connections to the branch circuit (for example, use of power
strips).

Attach the SG510 to the equipment mounting rack:

1 Position the SG510 into the equipment rack so that the ears of the brackets
align with the holes in the front of the rack.

2 Use equipment-rack screws to mount the SG510 to the equipment rack.
Figure 1-3 shows a SG510 flush-mounted on a Telco equipment rack.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 10

Use equipment-rack screws
to attach to the SG510 to the
rack

Figure 1-3: SG510 Attached to a Telco Equipment Rack

Attaching the Cable Management Support
The cable management support routes network serial cables to avoid tangling.
Fasten the cable management support to the back of the system as follows:

1 Position the cable management support at the back of the system on the right;
secure it with a 6-32 x 1/4 flathead screw at the side.

Attach the cable
management support with a
flathead screw

Figure 1-4: Attach the Cable Management Support

When you attach cables to the system, run them through this clip to keep
them from tangling.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 11

Installing the Disk Drives
The following instructions are for a first-time installation of the disk drives that
are shipped with the SG510. The drive slots on each end of the appliance contain
non-removable, blank disk-drive spacers.
Non-removable
spacer

Drive slot 1

Drive slot 2

Non-removable
spacer

Figure 1-5: Disk-Drive Slot Arrangement

Important: You cannot hot-swap disks in the SG510; you will lose all
configuration settings.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 12

Connecting the Cables
Connect the network cables, serial cable, and AC power cord.

AC Power

Serial port

Ethernet adapter
ports (Ports 0 and 1)

Figure 1-10: Connect the Cables to the Back of the System

1 Plug the network cable into adapter 0. Plug a second cable into the other
adapter if desired.
The two full-duplex, auto-sensing Ethernet network adapters supporting
10/100/1000 Base-T connections are labeled 0 and 1.

2 Plug the serial cable into the serial connector, if necessary.
If you attach the serial cable, you can connect the system to a PC, serial
terminal, or stand-alone Serial Console box.

3 Plug the enclosed power cord into the power cord receptacle.

Powering On the SG510
1 After you have connected the power cord to the rear of the system, plug the
other end of the power cord into a power receptacle.

2 Verify that the system has powered on successfully. See the four system states
described below and the corresponding states of the Power LED.

Power LED


No color: the SG510 is powered off or non-functional

P/N 231-02833

Blue Coat SG510 Installation Guide

page 16



Solid Amber: the SG510 is powered on but unable to perform tasks (for
example, while booting up)



Flashing Green to Amber: the SG510 is powered on but is not configured



Green: the SG510 is powered on and at least minimally configured

3 The three steps below show a typical, first-time, start-up sequence.


The Power LED lights up and the LCD becomes green and displays the
name Blue Coat.



The Power LED starts of solid amber and then begins flashing green and
amber.



After a moment, the disk drive LEDs corresponding to the disk drives
that are installed light up.



If you are connected to the network, the LAN LEDs light up.



The LCD displays IP address not configured (if a first-time configuration
has not been done) or it cycles between CPU utilization and the
hostname.
LCD

Power
LED

Disk Drive
LEDs (2)

LAN status
LEDs (2)

Figure 1-11: Verify Successful Power On

The SG510 comes with all software installed. To configure a SG510 for the first
time go to “Configure a SG510” on page 19.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 17

P/N 231-02833

Blue Coat SG510 Installation Guide

page 18

Chapter 2: Configure a SG510
You need to configure a SG510 the first time you power it on to set the basic
network parameters and to make sure that the SG510 hardware and software are
working properly.

Overview of First-Time Configuration
There are four ways to configure a SG510 the first time you power it on. Each of
these methods of configuring a SG510 let you make the basic network settings
required to test the connection and functionality.
Configuration
Method

Front Panel

Description
Use the front-panel LCD and buttons.
(This is the quickest and easiest way to do a first-time configuration.
To use the front panel method, go to “Configuring the SG510 with
the Front Panel Features” on page 21.

Serial Console

Use a direct connection between the system and a PC, or a serial
terminal, or a stand-alone serial console terminal.
To use the serial console connection, go to “Initial Configuration
Using a Direct Serial Port Connection” on page 38.

Web Browser

Use a Web browser. To use this method for SGOS 5.1.1.x and later,
you must first configure the IP address of the SG510 using the serial
console or front panel. Blue Coat recommends using the Web
browser configuration method if you are running SGOS 5.1.1.x or
later.
To use the Web browser configuration method, go to “Initial
Configuration with a Web Browser” on page 29.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 19

Configuration
Method

Remote
Configuration

Description
You can use this method if your appliance is running SGOS 4.2.2.x or
later. The remote configuration method is not supported for
appliances running 5.1.1.x or later.
Use two people to remotely configure the appliance—one who
enters the configuration parameters from a remote location and
another who places the SG510 into the network and finalizes the
configuration by clicking a generated URL.
To use the remote configuration method, go to “Configuring the

SG510 from a Remote Location” on page 55.
After you complete the first-time configuration, you must log on to the system
and use the command-line interface (CLI) or the Management Console graphical
user interface to fully configure the system. First-time configuration is designed
only to make sure that the SG510 hardware and software are working properly.
See “Logging on to the SG510” on page 62 for more information.
Refer to the Blue Coat ProxySG Configuration and Management Guide Suite for
information on how to fully configure the software. Download the Blue Coat
ProxySG Configuration and Management Guide Suite, available on the Blue Coat
Web site at www.bluecoat.com. (Look for WebPower Login under Support.)

P/N 231-02833

Blue Coat SG510 Installation Guide

page 20

Section A: Configuring the SG510 with the Front Panel
Features
You can configure a SG510 the first time you power it on using the front panel
LCD and control buttons.

Menu
button
Enter
button

LCD
Arrow buttons

Figure 2-1: Front Panel LCD and Control Buttons

Use the LCD and the buttons to monitor the system and to set the basic
networking parameters.

LCD Behavior
The default behavior of the front-panel LCD is to turn off after 30 seconds. The
front-panel LCD behavior is configurable; see “Configuring the Front-Panel LCD
Behavior” on page 68 for information.
To Turn the Front-Panel LCD Back On:


If the SG510 is powered on, but the front-panel LCD is off, press any
front-panel control button (see Figure 2-1) to turn the LCD back on.
After the LCD illuminates, the front-panel control buttons return to their
normal behavior.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 21

SG510 Control Buttons
Use the control buttons in conjunction with the modes as follows:
Enter Button

The Enter button functions as follows:
Status mode: When you push the Enter button in
Status mode, the system enters Configuration mode.
In Configuration mode, one of the six configurable
parameters displays in the LCD (starting with IP
address).
Configuration mode: When you push the Enter
button in Configuration mode, the system enters Edit
mode for the parameter displayed.
Edit mode: When you push the Enter button in Edit
mode, the system saves any changes you made to the
parameter displayed and returns to Configuration
mode.

Menu Button

The Menu button functions like an Escape key. When
you push the Menu button in Edit mode, the system
returns to Configuration mode, cancelling any changes
you made to the displayed parameter.
When you push the Menu button in Configuration
mode, the system returns to Status mode. Any
changes you made while in Edit mode have already
been saved, and are not affected when you push the
Menu button in Configuration mode.

Left and Right Arrow
Buttons

P/N 231-02833

When you push the Left and Right arrow buttons in
Edit mode, the cursor moves back and forth over the
configurable settings of the parameter displayed.

Blue Coat SG510 Installation Guide

page 24

Up and Down Arrow
Buttons

When you push the Up and Down arrow buttons in
Configuration mode, the system cycles through the
six configurable parameters.
When you push the Up and Down arrow buttons in
Edit mode, the system cycles through the characters
available for the selected setting of the parameter (the
selected setting is the character that the cursor is over
when you push the arrow buttons).

Using the Front Panel to Configure Basic Network
Settings
Use the front panel to do a quick first-time configuration of the following
networking parameters on Adapter 0:
• IP address

• Subnet mask

• Gateway address

• DNS address

• Console password

• Enable password

Important: A default username (admin) is already set on the SG510. A
unique console and enable password are generated
automatically. You can configure the passwords now, or write
down the auto-generated passwords and use them to log in,
changing them later. The enable password is not required if you
log in using a browser.

1 When the LCD displays “IP address not configured,” press the Enter button to
enter Configure mode.
The IP address parameter appears in the LCD, and the cursor appears as an
underscore.

2 Press the Enter button again to enter Edit mode.
The cursor changes to a blinking box.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 25

3 Press the Left or Right arrow buttons to position the cursor over the characters
you want to change; press the Up or Down arrow buttons to change them.

4 When you have all the characters of the parameter entered correctly, press the
Enter button to save the changes and return to Configure mode.

5 Press the Down arrow button to move to the next parameter; press the Enter
button to enter Edit mode.

6 Repeat Steps 3 through 5 for the Subnet mask, Gateway address, and DNS
address parameters. When the LCD reads, “Console password: Push to set,”
go to Step 7.

7 Press the Enter button to enter Edit mode (if necessary) and complete one of
the following steps:



To configure the password later (after you log in), write down the
auto-generated password and press the Enter button to return to
Configure mode.



To configure the password now, follow Steps 3 and 4.

8 Push the Down arrow button to move to the enable password parameter;
repeat Step 7 for the enable password.
The LCD displays “Enable password: Push to configure” when you are back
in Configuration mode. Do not push the Enter button again, or a new
auto-generated enable password will be created (if that happens, repeat
Step 7).

9 Push the Down arrow button to move to the secure serial port parameter.
Selecting Yes to secure the serial port means that you are challenged for the
administrative username/password when accessing the serial console and
challenged for the setup password when accessing the setup console.
To restrict access to the front panel, configure the front panel PIN from the
CLI after initial setup is complete (see “Configuring a Front-Panel PIN” on
page 67).

10 Press the Enter button to enter Edit mode (if necessary) and follow Steps 3 and
4 to secure the serial port.

11 Press the Menu button to return to Status mode.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 26

Initial network configuration is now complete. The LCD cycles between CPU
Utilization and Freshness statistics.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 27

Section B: Placing the SG510 into the Network
This procedure describes a a typical scenario for placing the SG510 into your
network. Use this procedure for the following circumstances:


You have already completed an initial configuration on the SG510.



You are going to complete an initial configuration on the SG510 using a direct
serial port connection or a remote Web browser setup.

The following instructions are an example of a typical network scenario—placing
the SG510 between the LAN and a router or firewall connected to the WAN. If
you do not know how to place the SG510 into your own network, consult with
your IT administrator. For less common network configurations, such as using
WCCP or a Layer 4 switch, refer to the Blue Coat ProxySG Configuration and
Management Guide Suite.
To Place the SG510 into the Network:

1 Connect the SG510 to the WAN—connect one end of an Ethernet cable
(straight or crossover depending on your network topology) to one of the
SG510’s Ethernet ports (either one). Connect the other end to the router or
firewall connected to the WAN.

2 Connect the SG510 to the LAN—connect one end of an Ethernet cable
(straight or crossover depending on your network topology) into the other
Ethernet port on the SG510. Connect the other end to the LAN (such as a PC
or a hub).

3 Verify that the network link is established by checking the network
connection LEDs at the back of the SG510. If the network connection is
functioning, the left-hand LED on each connection glows green.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 28

Section C: Initial Configuration with a Web Browser
This section describes how to configure the SG510 with a Web browser.

Requirements
To configure your SG510 using a browser, you must meet the following
requirements.


General Requirements


The browser must support Javascript and Javascript must be enabled.



The browser must not be proxied. For information about proxied
browsers, see “The Initial Configuration Page is Not Accessible” on page 78.



Your SG510 must not already be configured.
Note: If the SG510 has already been configured, you cannot access the
initial configuration page unless you reset the SG510 to factory
defaults as described in “Resetting the SG510 to Factory Defaults” on
page 81.



4.2.2.x Requirements
If the SG510 is running 4.2.2.x or later, you can access the 4.2.2.x initial
configuration Web page using one of the following methods:





Change the IP address of the PC so that it is on one of the subnets the
appliance uses for initial configuration. See “4.2.2.x—To Configure the
SG510 Using a Web Browser:” on page 30 for a list of initial configuration
IP addresses.



On the PC, create a static route to the SG510. Refer to “Creating A Static
Route to the SG510” on page 79 for information about creating a static
route.



Purchase and install the optional bridging card to deploy the SG510
inline.

5.1.1.x Requirements
If the SG510 is running 5.1.1.x or later, you must configure the SG510 IP
address, subnet mask, gateway, and DNS address using the front panel or
serial console before accessing the Setup Wizard.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 29

Where to go next
If your SG510 is running 4.2.2.x, complete the procedure described in “4.2.2.x—To
Configure the SG510 Using a Web Browser:” on page 30.
If your SG510 is running 5.1.1.x, complete the procedure described in “5.1.1.x—To
Configure the SG510 Using the Setup Wizard” on page 35.
4.2.2.x—To Configure the SG510 Using a Web Browser:
Before starting this procedure, ensure that you have met all requirements
described in“Requirements” on page 29.

1 Place the SG510 into the network.
For information on placing the SG510 into the network, see “Placing the SG510
into the Network” on page 28.

2 Power on the SG510.
3 Plug one end of the Ethernet cable into Port 0 on the back of the SG510.
4 Plug the other end of the Ethernet cable into your network.
5 Enter one of the following URLs into your browser (the browser must be on
the same subnet as the SG510 or you must have created a static route to one of
these addresses):
https://10.0.0.254:8083/
https://172.16.0.254:8083/
https://192.168.0.254:8083/
https://192.168.1.254:8083/

Note:

If you are using an inline bridging deployment, enter the following
URL into your browser: https://proxysg.bluecoat.com:8083/

P/N 231-02833

Blue Coat SG510 Installation Guide

page 30

A security warning dialog appears.

Note:

The appearance of the security warning dialog varies with browser
type.

6 Click Yes (or OK) in the dialog. The SG510 Initial Configuration window
opens.

Important: If you do not see the warning dialog or if you cannot connect to
the Initial Configuration page, see “The Initial Configuration Page is
Not Accessible” on page 78.

7 Enter the network parameters for your appliance.

Figure 2-2: Initial Configuration Page—Network Parameters

8 Enter the Console Account username and password and the Enable
(privileged mode) password. Do not select Password is in hashed format unless
the password is already in a valid hashed format.

Note:

If you want to have the password hashed for you, use the remote
initial configuration method (see Section E:Configuring the SG510
from a Remote Location).

P/N 231-02833

Blue Coat SG510 Installation Guide

page 31

Figure 2-3: Initial Configuration Page—Console Account Username and Password

9 Select the default policy for proxied services:


Selecting Allow permits all proxied transactions to pass through the
SG510; you must then create policies to explicitly deny proxied
transactions on a case-by-case basis.



Selecting Deny prohibits proxied transactions from passing through the
SG510; you must then create policies to explicitly grant proxied
transactions on a case-by-case basis.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 32

For more information about this option, refer to Volume 7: The Visual Policy
Manager and Advanced Policy Tasks of the Blue Coat ProxySG Configuration and
Management Guide Suite.

Figure 2-4: Initial Configuration Page—Default Policy for Proxied Services

10 (Optional) Secure the serial port: select Secure the Serial Port and enter the
password. Do not select Password is in hashed format unless the password is
already in a valid hashed format.
The serial port allows you to configure and access the SG510 using a serial
cable. This can pose a security risk, because anyone with access to the
appliance can reconfigure the SG510 settings. This step allows you to set a
password on the serial console setup, allowing only authorized personnel the
ability to reconfigure the appliance.

WARNING! If you set the serial console password and then lose the
password, you must restore the appliance to its original factory
defaults if you want to access the Management Console or CLI
(see “Resetting the SG510 to Factory Defaults” on page 81).

Figure 2-5: Initial Configuration Page—Secure the Serial Port
P/N 231-02833

Blue Coat SG510 Installation Guide

page 33

11 Click Configure Device.


If a dialog appears with the message Errors Found, click OK and correct the
errors in the Initial Configuration page. Click Configure Device again.



If a new browser window appears with the message The initial configuration
was not established, note the error messages in this window, close it, and
fix the appropriate data in the Initial Configuration page. Click Configure
Device again.



If a new browser window appears with the message ProxySG Initial
Configuration was successful, you have successfully completed initial
configuration. This window provides details about accessing the SG510
Management Console (such as the Management Console SHA1
fingerprint). Save this information for future reference. Close the new
browser window and the Initial Configuration page.

Figure 2-6: Successful Initial Configuration Page

When you have set the basic networking parameters and connected the SG510 to
the network, you are ready to fully configure the appliance. For a list of all CLI
commands, refer to the Blue Coat ProxySG Command Line Interface Reference. For
information about configuring and administering the SG510 (including
information about setting policies that will explicitly grant or deny proxied

P/N 231-02833

Blue Coat SG510 Installation Guide

page 34

transactions), refer to the Blue Coat ProxySG Configuration and Management Guide
Suite.
5.1.1.x—To Configure the SG510 Using the Setup Wizard
Before starting this procedure, ensure that you have met all requirements
described in“Requirements” on page 29.

1 Place the SG510 into the network.
For information on placing the SG510 into the network, see “Placing the SG510
into the Network” on page 28.

2 Power on the SG510.
3 Use the front panel or serial console to configure the SG510 IP address,
netmask, gateway address, and DNS address.

4 Enter the following URL into your browser:
https://IP_Address:8083/

In the preceding URL, IP_Address is the IP address you configured in Step 3.
A security warning dialog appears.

Note:

The appearance of the dialog varies depending on the browser that
you use.

5 Click Yes (or OK) in the dialog.

Important: If you do not see the warning dialog or if you cannot connect to
the Initial Configuration page, see “The Initial Configuration Page is
Not Accessible” on page 78.

When the appliance connects, the Setup Wizard displays, as shown in the
following figure.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 35

6 Enter information on each screen, as prompted.
Each page is described; some pages include mouse-over help. If you entered
network settings from the serial console, they are already filled in. To
complete the Setup Wizard you must:

a. Enter the console access information.
b. Enter the CLI Enable password.
c. (Optional but highly recommended) Secure the serial port.
d. Enter the network settings:


IP Address



Subnet Mask



Gateway



DNS Server

e. (Optional) Configure the Application Delivery Network (ADN) settings.
The ADN settings optimize the delivery of applications over the WAN.

f. Select the traffic types that the appliance should intercept.
g. Set the initial policy.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 36

h. Confirm the settings and click Configure.

Note:

The Web-based wizard is available only for initial appliance
configuration (or following a reset to factory defaults). After you
click Configure during the final step, the wizard is no longer available.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 37

Section D: Initial Configuration Using a Direct Serial
Port Connection
This section describes how to configure the SG510 using a direct serial port
connection. Before you can configure the SG510 using the serial port connection,
you must place the SG510 into the network as described in “Placing the SG510 into
the Network” on page 28.
A PC, serial terminal, or a stand-alone serial console terminal can be used to
configure a SG510 the first time you power it on. Use the serial console setup to
configure the following basic network information:
• IP address

• Subnet mask

• Gateway address

• DNS address

• Console username
and password

• Enable password

You can also configure a bridge or a forwarding host, or you can restrict access to
the SG510 to a particular IP address or set of IP addresses.

PC Note:

If the PC is using standard serial port settings, you should have
a problem-free connection. You can run into problems, though,
if there are non-standard PC serial port settings.

The serial port connection setup differs by model:


If your SG510 is running 4.2.2.x, complete the procedure described in
“4.2.2.x—Configuring the SG510 Using a Direct Serial Port Connection:” on
page 39.



If your SG510 is running 5.1.1.x, complete the procedure described in
“5.1.1.x—Configuring the SG510 Using a Direct Serial Port Connection:” on
page 47.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 38

4.2.2.x—Configuring the SG510 Using a Direct Serial Port Connection:
Do the following procedure by reading the on-screen material and entering data
where necessary. In the procedure below, places that require you to enter data are
illustrated by example entries in bold text.

1 Power on and connect (a) a serial terminal or (b) a PC as described below (the
SG510 must be powered off):
Serial terminal: Connect the terminal’s serial cable to the SG510’s serial
console port; start the terminal and verify that it is set using the RS-232C
parameters defined in the following table.
RS-232C Parameters
Parameter

Setting

Baud rate

9600 bps

Data bits

8

Parity

none

Stop bits

1

Flow control

none

Smooth-scroll

disabled

Emulation

VT 100

PC: Connect the serial cable that came with the SG510 to a serial port on the
PC and to the SG510’s serial console port; start the PC, open a terminal
emulator (such as HyperTerminal), and connect to the serial port to which
you attached the cable. Create and name a new connection (either a COM or
TCP/IP), and verify that the port is set using the parameters described in the
table above.

2 Power on the SG510 and wait for the system to finish booting.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 39

The following configuration alert displays:
******************* CONFIGURATION ALERT ******************
System startup cannot continue for one of these
reasons:
(a) Need at least one adapter (or bridge) configured
with an IP address and subnet.
(b) Need the console password and enable password.
********** SYSTEM STARTUP TEMPORARILY SUSPENDED

*********

Press "enter" three times to activate the serial console
Figure 2-7: Serial Port Setup—Configuration Alert

3 Press the computer keyboard key three times.
When the Welcome to the SG510 Appliance Setup Console prompt
appears, the system is ready for the first-time network configuration.
Five screens display, one at a time, as shown in the following steps.

4 On page 1, indicate whether you want to configure a bridge; enter an
interface number, and enter the values as indicated for the four network
settings.

Note:

If you enter YES to configure a bridge, you must also configure at
least one bridge port and associate a network interface with it.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 40

Welcome to the ProxySG Appliance Setup Console
---------------------- (page 1 of 5) --------------------Press at any time to return to the main menu
DIRECTIONS:
This setup console is used to assign IP addresses to
the ProxySG Appliance. After assigning the IP addresses
you can connect to the command line interface or Web
interface to perform additional management tasks.
If you have a pass through card, you can configure it by
using the bridge name passthru-. For
example if the pass through card is at slot 2, the
bridge name would be passthru-2.
In order to create a new bridge, you would have to
1. assign a name to the bridge
2. associate one or more interfaces to the bridge
Configure bridge? Y/N [No] No
Enter interface number to configure [0:0]:
IP address [0.0.0.0]: 10.25.36.47
IP subnet mask [0.0.0.0]: 255.255.255.0
IP gateway [0.0.0.0]: 10.25.36.1
DNS server [0.0.0.0]: 101.52.23.101
You have entered the following IP addresses:
IP address: 10.25.36.47
IP subnet mask: 255.255.255.0
IP gateway: 10.25.36.1
DNS server: 101.52.23.101
Would you like to change any of them? Y/N [No] No
Figure 2-8: Initial Setup—Page One

5

On page 2, enter a console username and a console and enable password. A
default username (admin) is already in place—you can change it here.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 41

Usernames and passwords can each be from 1 to 64 characters in length, and
that passwords that contain special characters (such as an exclamation point)
must be in quotes.
--------------------- (page 2 of 5) -------------------Press at any time to return to the main menu
DIRECTIONS:
The console username, password and enable password are
special administrative credentials which can be used to
log in to the command line interface or web management
interface.
WARNING - The console password and enable password are
not defined.
The system cannot start up until these are defined.
You must configure the console user account now.
Enter console username: name123
Enter console password: ”******”
Verify console password: ”******”
Enter enable password: ”******”
Verify enable password: ”******”
Figure 2-9: Initial Setup—Page Two

Note:

For maximum security, you should restrict physical access to the
SG510. After initial configuration, you can change the workstation
restriction settings through the security commands in the CLI or the
Console Access tab in the Management Console. You can add or
remove IP addresses or you can enable or disable workstation
restrictions. For details, refer to Volume 5: Securing the ProxySG in
the Blue Coat ProxySG Configuration and Management Guide Suite.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 42

6 (not recommended) For maximum security, you can secure the serial port.
The serial port allows you to configure and access the SG510 using a serial
cable. This can pose a security risk because anyone with access to the
appliance can reconfigure the settings. This optional step sets a password on
the serial console setup, allowing only authorized personnel the ability to
reconfigure the appliance. This is not recommended.

Note:

If you forget the serial port password for a SG510, you cannot get
access to the SG510.

Do you want to secure the serial port? Y/N [Yes] Yes
Enter setup password: ”******”
Verify setup password: ”******”
WARNING:
If you continue and enable the secure serial port it
will not be possible to enter the setup console
without the setup password. If the setup password is
lost, assistance from Blue Coat Systems will be
required and all system configuration may be lost.
It is recommended that this password be stored in a
physically secure location. Access to the CLI on the
serial port will challenge for credentials.
To enable the secure serial port, re-enter the setup
password: ”******”
Figure 2-10: Initial Setup—Secure the Serial Port (not recommended)

P/N 231-02833

Blue Coat SG510 Installation Guide

page 43

7 (Optional) On page 3, you can restrict access to the SG510.
--------------------- (page 3 of 5) -------------------Press at any time to return to the main menu
DIRECTIONS:
The console username and password are special: they can
be used to log in to the CLI or Web Management
interface even in circumstances where this is denied by
VPM or CPL policy. This makes the console account
useful in emergencies, as a way to log in when policy
is broken, but it may also create a security hole.
To close the security hole, we recommend that you
restrict the use of the console account to specific
workstations, identified by their IP address.
This dialog allows you to add one IP address to the
list of workstations that are authorized to use the
console account. (This same list is also used to
restrict which workstations can use SSH with RSA
authentication.) Additional workstations may be
configured later, from the command line interface or
the Web interface.
WARNING: The console account can currently be used to
log in from any workstation.
Would you like to restrict access to an authorized
workstation? Y/N [Yes] Yes
Authorized workstation [0.0.0.0]:10.2.33.1
Figure 2-11: Initial Setup—Page Three

P/N 231-02833

Blue Coat SG510 Installation Guide

page 44

8 On page 4, press or type No if you do not want to enter a forwarding
host at this time, or type Yes to enter a forwarding host.
If you type Yes, you must also provide a host alias and a host name or IP
address.

Note:

You do not need to configure a forwarding host now unless
you are configuring multiple systems to point to the same
forwarding host.

--------------------- (page 4 of 5) -------------------Press at any time to return to the main menu
DIRECTIONS:
This setup console is used to configure a proxy
forwarding host as the forwarding default (a one member
default fail-over sequence). After assigning a host
alias and the host name you can connect to the command
line interface to perform additional management tasks.
Would you like to setup the forwarding host now? Y/N [No]
Figure 2-12: Initial Setup—Page Four

P/N 231-02833

Blue Coat SG510 Installation Guide

page 45

Page 5 displays. This page explains how to access the SG510 from an SSH
Client or with a Web browser (see “Logging on to the SG510” on page 62 for
more information).
---------------------- (page 5 of 5) --------------------DIRECTIONS:
The ProxySG Appliance has been successfully configured
to use IP address: "10.25.36.47"
You can connect to the command line interface or Web
interface to perform additional management tasks.
To connect to the command line interface, open the
following location from your SSH application:
10.9.16.85
To connect to the Web management interface, go to the
following location with your web browser:
https://10.9.16.85:8082/
---------------- CONFIGURATION COMPLETE -----------------Press "enter" three times to activate the serial console
Figure 2-13: Initial Setup—Page Five

9 To log in to the serial console right away, press three times.
A menu displays, offering two choices:
1) Command Line Interface
2) Setup Console

10 Enter 1 to select the CLI (see “Logging on to the SG510 CLI” on page 64 for
information about using the SG510 CLI). To access the SG510 Management
Console, enter the following address into your Web browser:
https://[IP Address]:8082/

where [IP Address] is the IP address that you configured for this SG510 in
Step 4.
See “Logging on to the SG510 Management Console” on page 62 for more
information about accessing the SG510.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 46

5.1.1.x—Configuring the SG510 Using a Direct Serial Port Connection:
Do the following procedure by reading the on-screen material and entering data
where necessary. In the procedure below, places that require you to enter data are
illustrated by example entries in bold text.

1 Power on and connect the serial terminal or PC as described below (the SG510
must be powered off):
Serial terminal: Connect the terminal’s serial cable to the SG510’s serial
console port; start the terminal and verify that it is set using the parameters
described below.
RS-232C Parameters
Parameter

Setting

Baud rate

9600 bps

Data bits

8

Parity

none

Stop bits

1

Flow control

none

Smooth-scroll

disabled

Emulation

VT 100

PC: Connect a serial cable to a serial port on the PC and to the SG510’s serial
console port; start the PC, open a terminal emulator (such as HyperTerminal),
and connect to the serial port to which you attached the cable. Create and
name a new connection (either a COM or TCP/IP), and verify that the port is
set using the parameters described in the preceding table.
If you have set flow control to none, and if you have smooth-scroll as an option
in your terminal settings, you can disable smooth-scroll in your terminal
settings to reduce the chance of losing output.

2 Power on the SG510 and wait for the system to finish booting.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 47

The following configuration alert displays:
****************** CONFIGURATION ALERT ******************
System startup cannot continue for one of these reasons:
(a) Need at least one adapter (or bridge) configured with an I
address and
subnet.
(b) Need the console password and enable password.
********* SYSTEM STARTUP TEMPORARILY SUSPENDED

*********

Press "enter" three times to activate the serial console
Figure 2-14: Initial Setup—Configuration Alert

3 Press three times.
When the Welcome to the ProxySG Appliance Setup Console prompt
appears, the system is ready for the first-time network configuration.

4 On page 1, enter the interface number, IP address, IP subnet mask, IP
gateway, and DNS server parameters.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 48

Welcome to the ProxySG Appliance Setup Console
--------------------- (page 1 of 5) -------------------Press at any time to return to the main menu
DIRECTIONS:
This setup console is used to assign IP addresses to the ProxyS
Appliance. After assigning the IP addresses you can connect to
command line interface or Web interface to perform additional
management tasks.
Enter interface number to configure [0:0]:
IP address [0.0.0.0]: 10.25.36.47
IP subnet mask [255.255.255.0]: 255.255.255.0
IP gateway [0.0.0.0]: 10.25.36.1
DNS server [0.0.0.0]: 101.52.23.100
You have entered the following IP addresses:
IP address: 10.25.36.47
IP subnet mask: 255.255.255.0
IP gateway: 10.25.36.1
DNS server: 101.52.23.101
Would you like to change any of them? Y/N [No] N
Figure 2-15: Initial Setup—Page One

5 On page 2, you are asked if you want to finish configuration using the Setup
Wizard.

--------------------- (page 2 of 5) -------------------A comprehensive Setup Wizard is available if you use your
Web browser. You can either use the Web Setup Wizard or you
can continue the initial configuration using this serial console.
Note that this serial console initial configuration method
contains a subset of the configuration options available in the
Web Setup Wizard.

Figure 2-16: Initial Setup—Page Two

P/N 231-02833

Blue Coat SG510 Installation Guide

page 49

If you choose to use the Setup Wizard, go to “5.1.1.x—To Configure the SG510
Using the Setup Wizard” on page 35.

6 On page 3, enter a console username and a console and enable password. A
default username (admin) is already in place—you can change it here.
Usernames and passwords can each be from 1 to 64 characters in length.
Passwords that contain special characters (such as an exclamation point) must
be in quotes.
---------------------- (page 3 of 5) --------------------Press at any time to return to the main menu
DIRECTIONS:
The console username, password and enable password are special
administrative credentials which can be used to log in to the comman
line interface or web management interface.
WARNING - The console password and enable password are not defined
The system cannot start up until these are defined.
You must configure the console user account now.
Enter console username [admin]: name123
Enter console password: ”******”
Verify console password: ”******”
Enter enable password: ”******”
Verify enable password: ”******”
Figure 2-17: Initial Setup—Page Three

7 (not recommended) For maximum security, secure the serial port.
The serial port allows you to configure and access the SG510 using a serial
cable. This can pose a security risk because anyone with access to the
appliance can reconfigure the SG510 settings. This optional step sets a
password for the serial console setup, allowing only authorized personnel the
ability to reconfigure the appliance.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 50

WARNING! If you set the serial console password and then lose the
password, you must restore the appliance to its original factory
defaults to access the Management Console or CLI (see
“Resetting the SG510 to Factory Defaults” on page 81).

Do you want to secure the serial port? Y/N [Yes] Y
Enter setup password: ”******”
Verify setup password: ”******”
WARNING:
If you continue and enable the secure serial port it
will not be possible to enter the setup console without
the setup password. If the setup password is lost,
assistance from Blue Coat Systems will be required and
all system configuration may be lost. It is recommended
that this password be stored in a physically secure
location. Access to the CLI on the serial port will
challenge for credentials.
To enable the secure serial port, re-enter the setup
password: ”******”
Figure 2-18: Initial Setup—Secure the Serial Port (Optional)

8 (Optional) On page 4, you can restrict access to the SG510.

Note:

For maximum security, you should restrict physical access to the
SG510.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 51

--------------------- (page 4 of 5) -------------------Press at any time to return to the main menu
DIRECTIONS:
The console username and password are special: they can be used t
log in to the CLI or Web Management interface even in circumstanc
where this is denied by VPM or CPL policy. This makes the console
account useful in emergencies, as a way to log in when policy is
broken, but it may also create a security hole.
To close the security hole, we recommend that you restrict the use
the console account to specific workstations, identified by their
address.
This dialog allows you to add one IP address to the list of
workstations that are authorized to use the console account. (Thi
same list is also used to restrict which workstations can use SSH
with RSA authentication.) Additional workstations may be configur
later, from the command line interface or the Web interface.
WARNING: The console account can currently be used to log in from a
workstation.
Would you like to restrict access to an authorized workstation? Y
[Yes] Y
Authorized workstation [0.0.0.0]:10.2.33.1
Figure 2-19: Initial Setup—Page Four

Page 5 displays. This page explains how to access the SG510 from an SSH
Client or with a Web browser. See “Logging on to the SG510” on page 62 for
more information.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 52

--------------------- (page 5 of 5) -------------------DIRECTIONS:
The ProxySG Appliance has been successfully configured to
use IP address: "10.25.36.47"
You can connect to the command line interface or Web
interface to perform additional management tasks.
To connect to the command line interface, open the following
location from your SSH application: 10.25.36.47
To connect to the Web management interface, go to the
following location with your web browser:
https://10.25.36.47:8082/
--------------- CONFIGURATION COMPLETE ----------------Press "enter" three times to activate the serial console
Figure 2-20: Initial Setup—Page Five

9 To log in to the serial console right away, press three times.
A menu displays offering two choices:
1) Command Line Interface
2) Setup Console

10 Access the CLI or Management Console:


Enter 1 in the serial console menu to select the CLI.
See “Logging on to the SG510 CLI” on page 64 for information about using
the SG510 CLI.



To access the SG510 Management Console, enter the following address
into your Web browser:
https://proxysg_IP:8082/

where proxysg_IP is the IP address that you configured for this SG510.
See “Logging on to the SG510 Management Console” on page 62 for more
information about accessing the SG510.
When you have set the basic networking parameters and connected the SG510 to
the network, you are ready to fully configure the appliance. For a list of all CLI
commands, refer to the Blue Coat ProxySG Command Line Interface Reference. For
P/N 231-02833

Blue Coat SG510 Installation Guide

page 53

information about configuring and administering the SG510 (including
information about setting policies that will explicitly grant or deny proxied
transactions), refer to the Blue Coat ProxySG Configuration and Management Guide
Suite.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 54

Section E: Configuring the SG510 from a Remote
Location

Important: The remote configuration procedure pertains only to 4.2.2.x or
later. If you are running 5.1.1.x or later, you must configure the
SG510 using the front panel, Web Setup Wizard, or serial
console. See “5.1.1.x—To Configure the SG510 Using the Setup
Wizard” on page 35 and “5.1.1.x—Configuring the SG510 Using a
Direct Serial Port Connection:” on page 47 for more information.

The goal of the remote configuration method is to allow an administrator to
provide the initial configuration settings of an appliance before the physical
installation of the system. Using the remote configuration method, an
administrator uses an HTML page to specify the initial configuration settings,
which are then embedded into a URL. To configure the appliance, a remote
installer only has to place the appliance into the network and click the generated
URL. After the appliance has its initial configuration, the administrator can finish
configuring the appliance—either remotely or locally.
The remote configuration method is useful in the following circumstances:


You have appliances destined for multiple locations but do not want to have
to first ship them to a single location for initial configuration.



The personnel at the remote locations are not technical and cannot be trusted
to properly configure the appliance.

Configuring the SG510 remotely is a two-step process—use the following
procedures if you want to enter the SG510 configuration parameters from a
remote location (Step 1), and then have an on-site administrator place the SG510
into the network and complete the configuration (Step 2).

Step One—Enter the Remote Configuration Parameters Using
a Web Browser
Perform this procedure if you plan to enter configuration parameters for the
SG510 from a remote location and then have an on-site administrator place the
SG510 into the network and complete the configuration.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 55

To Enter Configuration Parameters from a Remote Location:

1 Enter the following URL into your browser:
http://download.bluecoat.com/initial-remote/initial-remote.html

2 The SG510 Initial Configuration Setup for Remote Appliances window opens.
3 Enter the network parameters for the remote appliance.

Figure 2-21: Remote Initial Configuration Page—Network Parameters

P/N 231-02833

Blue Coat SG510 Installation Guide

page 56

4 Enter the Console Account username and password; enter the Enable
(privileged mode) password.


If you enter the passwords in plain text, click hash the password for each
password.



If you enter the passwords in hashed format, select password is in hashed
format for each password. A hashed password must be in the BSD MD5
password format.

Figure 2-22: Remote Initial Configuration Page—Console Account Username
and Password

P/N 231-02833

Blue Coat SG510 Installation Guide

page 57

5 Select the default policy for proxied services:


Selecting Allow permits any and all proxy-types access to the SG510; you
must then create policies to explicitly deny access on a case-by-case basis.



Selecting Deny prohibits proxy-type access to the SG510; you must then
create policies to explicitly grant access on a case-by-case basis.

For more information about this option, refer to Volume 7: The Visual Policy
Manager and Advanced Policy Tasks of the Blue Coat ProxySG Configuration and
Management Guide Suite.

Figure 2-23: Remote Initial Configuration Page—Default Policy for Proxied Services

6 (Optional) Secure the serial port: select Secure the Serial Port and enter the
password.


If you enter the password in plain text, click hash the password.



If you enter the password in hashed format, select password is in hashed
format. A hashed password must be in the BSD MD5 password format

The serial port allows you to configure and access the SG510 using a serial
cable. This can pose a security risk, because anyone with access to the
appliance can reconfigure the SG510 settings. This optional step allows you to
set a password on the serial console setup, allowing only authorized
personnel the ability to reconfigure the appliance.

WARNING! If you set the serial console password and then lose the
password, you must restore the appliance to its original factory
defaults to access the Management Console or CLI (see
“Resetting the SG510 to Factory Defaults” on page 81).

P/N 231-02833

Blue Coat SG510 Installation Guide

page 58

Figure 2-24: Remote Initial Configuration Page—Secure the Serial Port

7 Click Generate URLs.


If a dialog appears with the message Errors Found, click OK and correct the
errors in the Initial Configuration page. Click Generate URLs again.



If all the fields in the form are correct, a section called Configuration
URLs appears at the bottom of the page. A list of URLs are provided in
this section—one for each of the five potential network addresses to
which the SG510 might respond. Which URL works best depends on the
network topology into which the SG510 is placed. At least one of the
URLs should work in your network environment.

8 Copy and send one or more of the URLs to the local administrator who will
complete the configuration. Verify that the local administrator has all
required information, such as how to properly place the SG510 into the
network and, if necessary, how to modify the network parameters on his or
her PC so that the generated URL works to configure the appliance.

Step Two—Complete the Configuration
Perform the following procedure if you are at the same location as the SG510 and
you are planning to complete the initial configuration using a URL provided to
you by a remote administrator.
To Configure the SG510 Using a Remotely Generated URL:

1 Place the SG510 into your network using one of the following methods:


Change the IP address of the PC so that it is on one of the subnets the
appliance uses for initial configuration:
https://10.0.0.254:8083/

P/N 231-02833

Blue Coat SG510 Installation Guide

page 59

https://172.16.0.254:8083/
https://192.168.0.254:8083/
https://192.168.1.254:8083/


On the PC, create a static route to the SG200. Refer to “Creating A Static
Route to the SG510” on page 79 for information about creating a static
route.



Deploy the SG200 inline using the bridging feature.

Refer to Volume 2: Getting Started of the Blue Coat ProxySG Configuration and
Management Guide Suite for more information about these deployments.

2 On your PC, open a Web browser using the Initial Configuration URL that
you received from the remote administrator. If the URL is a link in an e-mail,
click the link.



If a new browser window appears with the message ProxySG Initial
Configuration was successful, you have successfully completed initial
configuration. This window provides details about accessing the SG510
Management Console, including the Management Console SHA1
fingerprint (see Figure 2-6 on page 34). Save this information for future
reference. Close the new browser window and the Initial Configuration
page.



If the URL was not entered correctly or was corrupted, an error page
displays. Fix the problem indicated and click Configure Device again.



If the SG510 is unavailable (for example, it is not connected to the
network properly or is already configured), you either fail to connect to
the Web page (and see a browser error page), or you see a Blue Coat Web
page that describes some of the potential problems you might have. Fix

P/N 231-02833

Blue Coat SG510 Installation Guide

page 60

the problem, if possible, and click Configure Device again. If you cannot fix
the problem, contact the remote administrator for assistance.

Note:

You might need to modify the network parameters on your PC so
that the URL works to configure the SG510. Consult the remote
administrator if you suspect that this is required.

When you have set the basic networking parameters and connected the SG510 to
the network, you are ready to fully configure the appliance. For a list of all CLI
commands, refer to the Blue Coat ProxySG Command Line Interface Reference. For
information about configuring and administering the SG510 (including
information about setting policies that will explicitly grant or deny proxied
transactions), refer to the Blue Coat ProxySG Configuration and Management Guide
Suite.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 61

Section F: Logging on to the SG510
After the SG510 is configured, the LCD will begin to cycle through and display
various messages, such as CPU Utilization and Freshness.
After you have completed the initial configuration and connected the SG510 to
the network, you must log on to the SG510 to fully configure the appliance. There
are two ways to do this.


Use a browser to access the SG510 Management Console Web interface.



Use a direct serial connection or an SSH Client to access the SG510
command-line interface (CLI).

Important: Blue Coat recommends that you set up a secure SSL connection
for greater security. For instructions, refer to Volume 5:
Securing the ProxySG in the Blue Coat ProxySG Configuration
and Management Guide Suite.

Logging on to the SG510 Management Console
The Management Console is a graphical interface for configuring and managing
all aspects of the SG510. You can log on to the Management Console using a
browser.
To Log on to the Management Console Using a Browser:

1 Start the SG510.
2 Open a browser. The SG510 supports Microsoft® Internet Explorer 6.0,
Netscape® Communicator 7.2, and Firefox 1.0.

3 Enter the IP address configured during initial configuration, followed by the
port number 8082. For example, enter: https://10.25.36.47:8082.

4 Click Yes in the Security Alert dialog; enter a username and password in the
Enter Network Password dialog that displays. If the username has not been
changed, the default is admin. The password is the one you wrote down or
configured during initial configuration.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 62

The SG510 home page displays.

5 Click the Management Console link from the top of the list on the left.
The Management Console page displays.

Figure 2-25: The Management Console Page

6 Navigate among Configuration, Maintenance, and Statistics by clicking one
of the three tabs near the top of the screen; click the links on the left to select a
configurable component. Click the Help button on any screen to display
information for that screen.
The online Help contains the complete text of the Blue Coat ProxySG
Configuration and Management Guide Suite. Use the Contents and Index links to
navigate through the manual.
When you have set the basic networking parameters and connected the SG510 to
the network, you are ready to fully configure the appliance. Refer to the Blue Coat
ProxySG Configuration and Management Guide Suite for information about
configuring and administering the SG510. For information about configuring
explicit or transparent proxies for the SG510, refer to Volume 3: Proxies and Proxy
Services of the Blue Coat ProxySG Configuration and Management Guide Suite. For a
list of all CLI commands, refer to the Blue Coat ProxySG Command Line Interface
Reference.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 63

Logging on to the SG510 CLI
You can connect to the SG510 CLI (a) by using a direct serial connection or (b) by
using an SSH client, such as PuTTY or F-Secure. To connect to the SG510 CLI using
Telnet, you must first enable the Telnet-Console. Refer to the Volume 3: Proxies and
Proxy Services of the Blue Coat ProxySG Configuration and Management Guide Suite.

Note:

The CLI uses two passwords: The console password is required to
establish a connection to the interface, and the enable password
can be set to restrict access to the privileged mode configuration
options. If you forget the username or password, you can reset them
using either the front panel control buttons and LCD or a serial
terminal or PC.

Using a Direct Serial Connection to Connect to the SG510 CLI

1 To set up the serial connection, complete steps 1 and 2 in the section “Initial
Configuration Using a Direct Serial Port Connection” on page 38.

2 After the system has finished booting, press the computer keyboard Enter key
three times. The following text displays:
Welcome to the Appliance Serial Console
Version: SGOS 4.2.2.0, Release id: 12345
------------------------- MENU--------------------------1) Command Line Interface
2) Setup Console
-------------------------------------------------------Enter option:

3 Enter 1 to select the Command Line Interface option.
4 Enter the username and password when prompted. If the username has not
been changed, the default is admin. The password is the one you wrote down
or configured during initial configuration.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 64

5 At the command prompt, enter enable, then enter the enable password that
you wrote down or configured during initial configuration:
SGOS>enable
Enable Password:
SGOS#

You are now in privileged mode.

6 At the privileged-mode command prompt, enter configure

terminal to

configure SG510 settings:
SGOS# configure terminal
Enter configuration commands, one per line. End with CTRL-Z.
SGOS#(config)

Refer to the Blue Coat ProxySG Configuration and Management Guide Suite for
information about configuring and administering the ProxySG.
Using an SSH Client to Connect to the SG510 CLI

1 Start the ProxySG.

Note:

You must already have an SSH Client installed before you proceed
with the steps below.

2 Launch your SSH Client—enter the following settings as necessary:


The IP address that you configured during initial configuration.



A port number, if necessary. (Port 22 is the default.)



The username and password. If the username has not been changed, the
default is admin. The password is the one you wrote down or configured
during initial configuration.

3 At the command prompt, enter enable, then enter the enable password that
you wrote down or configured during initial configuration:
SGOS>enable
Enable Password:
SGOS#

You are now in privileged mode.
P/N 231-02833

Blue Coat SG510 Installation Guide

page 65

4 At the privileged-mode command prompt, enter configure

terminal to

configure ProxySG settings:
SGOS#configure terminal
[Enter configuration commands, one per line. End with CTRL-Z.]
SGOS#(config)

Refer to the Blue Coat ProxySG Configuration and Management Guide Suite for
information about configuring and administering the ProxySG.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 66

Section G: Configuring a Front-Panel PIN
The front panel allows you to reconfigure the initial settings of the SG510, which
can represent a security risk. Setting a front-panel PIN limits access to authorized
personnel only.
This procedure is only available through the CLI—you cannot set a front-panel
PIN through the Management Console.
To Configure a Front-Panel PIN:

1 Connect to the SG510 CLI and access the privileged-mode configure
commands (see “Logging on to the SG510” on page 62).

2 From the privileged mode command prompt, change the SG510 front panel
PIN by entering one of the following commands:
SGOS#(config) security front-panel-pin PIN

-orSGOS#(config) security hashed-front-panel-pin hashed_PIN

where PIN is an unhashed PIN and hashed_PIN is a PIN in hashed format.
After entering one of these commands, anyone who attempts to configure the
SG510 through the front panel is prompted to enter the PIN.

Note:

The front-panel PIN commands are hidden commands. If you enter
the commands listed above and receive an unrecognized command
message, enter the following command and try again:
SGOS#(config) reveal-advanced all

P/N 231-02833

Blue Coat SG510 Installation Guide

page 67

Section H: Configuring the Front-Panel LCD Behavior
The front-panel LCD turns off after 30 seconds by default. This behavior is
configurable—you can set the LCD to remain on at all times, to turn off after a
specified length of time, or to flash (the flash setting can be helpful if you need to
find one SG510 in a room full of them).
The front-panel LCD cannot be configured through the Management
Console—you must use the CLI.
To Configure the Front-Panel LCD through the CLI:

1 Open a terminal session with the SG510; at the standard-mode command
prompt, enter enable and your privileged-mode password.
SGOS>enable
Enable Password: ******
SGOS#

2 At the privileged-mode command prompt, enter the configure

terminal

command to access the privileged mode configure commands:
SGOS#configure terminal
SGOS#(config)

3 At the (config) prompt, enter the front-panel command to access the
front-panel mode commands and to configure the front-panel LCD behavior.
SGOS#(config) front-panel
SGOS#(config front-panel)
SGOS#(config front-panel) backlight flash
SGOS#(config front-panel) backlight state {off | on | timeout}
SGOS#(config front-panel) backlight timeout seconds

P/N 231-02833

Blue Coat SG510 Installation Guide

page 68

where:
Configures the LCD to flash. When set, the LCD
continues to flash until the user presses a front panel
button or the setting is changed through the CLI
command no backlight flash.

flash

The flash setting can overwrite the backlight state
setting.
state

timeout

P/N 231-02833

off

Configures the LCD to always remain off when the
ProxySG is powered on. This is the default behavior.

on

Configures the LCD to always remain on when the
SG510 is powered on.

timeout

Configures the LCD to turn off after a specified
number of seconds. Use the backlight timeout
seconds command (described below) to specify the
number of seconds.

seconds

Specifies the number of seconds that the LCD
remains on without activity. The backlight
state timeout command specifies an LCD
timeout; this command specifies the number of
seconds before timeout occurs.

Blue Coat SG510 Installation Guide

page 69

P/N 231-02833

Blue Coat SG510 Installation Guide

page 70

Chapter 3: Removing and Installing Disk Drives
This chapter describes how to remove and install disk drives.

Important: The SG510 only supports disk-drive upgrade packages obtained
from Blue Coat Systems, Inc.

Important: You cannot hot-swap disks in the SG510; you will lose all
configuration settings.

A SG510 Appliance has open slots for two disk drives. The unit ships with two
blank disk-drive spacers already installed. Do not attempt to remove these blank
drives.
If your original appliance came with a single disk drive, upgrade options are
available from Blue Coat.
If you are upgrading your SG510 by adding (not replacing) disk drives, you can
skip to “Installing a New Disk Drive” on page 73.
For initial installation of disk drives into a new SG510, see “Installing the Disk
Drives” on page 12.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 71

5 Carefully pull the lever towards you to slide the disk drive out.
First press this button to
release the lever

Pull the lever toward you to slide the
disk drive carrier out

Figure 3-28: Slide the Disk Drive Out

Installing a New Disk Drive
Follow these steps to install a new disk drive.

Note:

The SG510 must be powered off before installing a new disk drive.

1 Take the new disk drive and press the button to release the lever.
2 Align the drive carrier with the guide rails of the drive slot. Using the lever,
carefully insert the drive carrier into the slot.

3 When the disk meets the drive slot wall, gently rotate the lever towards the
button until it latches, seating the drive firmly in place.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 73

4 Slide in the front panel tray, if necessary, and close the front panel.
5 Power up the SG510.
The SG510 recognizes and initializes the disk; no configuration is necessary.
When the new disk is plugged in, the corresponding Disk Drive LED lights up to
show that the drive is online.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 74

Chapter 4: Option Cards
The SG510 comes with a number of expansion slots; three option cards are
available.

Dual Gigabit Ethernet 1000B-SX (optical) Card
This card provides one gigabit of throughput to the network.

Dual Gigabit Ethernet (copper) Pass-Through Card
This card is a two-port, PCI network interface card (NIC). The Pass- Through
Card has three separate functions:


It works as a standard NIC to move data in and out of the SG510.



It provides a hardware failover mechanism in case of a power loss to or
hardware or software failure in the SG510. In the event of any of the above,
the Pass-Through card will physically bypass Ethernet traffic around the
SG510.



It does away with the need for a router or Layer 4 switch when the SG510 is
configured for transparent proxy by working with Layer 4 redirection
software in the SGOS operating system.

SSL Accelerator Card
This PCI card enables the SSL proxy service to intercept HTTPS traffic (in explicit
and transparent modes) so that security measures such as authentication, virus
scanning and URL filtering, and performance enhancements such as HTTP
caching can be applied to HTTPS content. Additionally, the SSL proxy allows you
to validate server certificates presented by various HTTPS sites at the gateway
and offers information about the HTTPS traffic in the access log.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 75

P/N 231-02833

Blue Coat SG510 Installation Guide

page 76

Chapter 5: Troubleshooting
This chapter describes how to isolate and solve common problems during the
installation of the SG510.

The SG510 does not power up
If the SG510 does not power up, check the following:


The power cord is fully inserted into the back of the SG510.



The power cord is plugged into a working outlet or power supply.

When the SG510 is powered up and running, the Power LED on the front panel of
the SG510 is on, the Disk Drive LEDs (for as many disks as are installed) are on,
and the LCD displays Blue Coat when starting up and then the LCD cycles
between CPU utilization and proxied traffic statistics when the SG510 is running.
Power LED

LCD

Figure 5-1: SG510 Powering Up

P/N 231-02833

Blue Coat SG510 Installation Guide

page 77

The Initial Configuration Page is Not Accessible
This is a networking problem or you entered an incorrect network address.
Attempt the following:


Verify that the SG510 is powered on.



Verify that both interfaces have established a network link.



If you are using a bridged deployment, verify that you entered the correct
initial configuration URL: https://proxysg.bluecoat.com:8083/



Try one of the following URLs to access the Initial Configuration page:
https://10.0.0.254:8083/
https://172.16.0.254:8083/
https://192.168.0.254:8083/
https://192.168.1.254:8083/

To use the preceding URLs, the host client has to be in the same subnet as one
of the IP addresses. Or, you can add a static route on the host client.


Verify that the browser is not proxied. To change or check the browser
settings, complete one of the following steps:


In a Windows browser, select Tools>Internet Options>Connections. Click
LAN Settings and deselect Proxy server if it is selected.



In a Firefox browser, select Tools>Options>General. Click the Connection
Settings button and deselect Manual or Automatic Proxy Configuration if one
of them is selected (select Direct Connection to the Internet).



In a Netscape Communicator browser, select
Edit>Preferences>Advanced>Proxies and deselect Manual or Automatic Proxy
Configuration if one of them is selected (select Direct Connection to the
Internet).



Restore the appliance to its factory defaults (the Initial Configuration page is
not accessible to an appliance that has already been configured). See
“Resetting the SG510 to Factory Defaults” on page 81.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 78

Creating A Static Route to the SG510
I f your SG510 is running 4.2.2.x or later and you want to use the Web-based
initial configuration method, you might need to create a static route from your PC
to one of the “soft” initial configuration IP addresses.
To create a static route to the SG510

1 Access the Windows command prompt.
2 Enter the following command:
C:\>route add proxySG_ip_address mask subnet_mask client_ip_address

In the preceding command, soft_ip_address is one of the “soft” IP addresses the
SG510 listens for and client_ip_address is the address of the PC.
For example:
C:\>route add 10.0.0.254 mask 255.255.255.255 10.2.11.155

3 Verify the static route by entering the following command:
C:\>route print

You cannot access the serial console
If you have connected a serial cable to the SG510 but you cannot open the serial
console, do the following:


Check cable connections.



Check configuration information at the terminal emulator for the correct
settings (see “Initial Configuration Using a Direct Serial Port Connection” on
page 38 for information).



Verify that the serial cable is a Null Modem type cable. The cable pin outs can
be found at http://www.bluecoat.com/support/self-service/1/pinouts.html



Use a different cable.

You cannot access the Management Console
If the browser fails to connect to the SG510 successfully, complete the following
steps to identify the problem.


Verify that you have the correct IP address and port for the SG510 in your
Web browser (the default port is 8082).

P/N 231-02833

Blue Coat SG510 Installation Guide

page 79

Verify the address and port using the CLI through the Serial Console, and
display the network configuration. For information on how to do this, see
“Initial Configuration Using a Direct Serial Port Connection” on page 38.


Verify that the workstation is configured and working properly by
connecting to other Web sites. This test might fail if your browser is
configured to use the SG510 as a proxy server and there is a problem with the
SG510.



If accessing a SG510 located on a remote network (any segment other than the
segment to which the workstation is attached), verify that other servers on
that network are accessible.



Ping the IP address to verify that the SG510 is accessible from the
workstation. If the SG510 does not respond to the ping, verify that the SG510
is operational (as described earlier).

A Security Warning Appears for the Initial
Configuration Web Page
When you open the Initial Configuration page, a security warning dialog appears.
This warning indicates that the SG510 credentials could not be verified by a
known certificate authority (such as VeriSign®). This is because the SG510
dynamically generated the self-signed credentials at the time of the last factory
reset—they are not registered with a known certificate authority.
Normally, accepting such a credential represents a security risk because of the
possibility of a man-in-the-middle attack. However, when you have connected
your PC directly to the SG510, as described in this guide, a man-in-the-middle
attack is impossible. The SG510 has not yet been configured and is connected
directly to your PC. The Initial Configuration Web page is accessible only through
a SG510 that has not yet been configured.
You can verify that the serial number in the credential matches the serial number
printed on the SG510 if you want to be absolutely certain that you have connected
to the correct device.

The SG510 certificate is no longer valid
If you move the SG510 from its original location or change the IP address for any
reason, the SG510’s security certificate might not be accepted the next time you
open the Management Console.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 80

This is because the hostname no longer matches the hostname on the certificate.
You must create a new certificate and then edit the HTTPS-Console service to use
it.
For information about creating a new certificate and editing the HTTPS-Console
service, refer to the “Configuring HTTPS Termination” and “HTTPS Console
(Secure Console)” sections of the Blue Coat ProxySG Configuration and Management
Guide Suite.

Resetting the SG510 to Factory Defaults
When the SG510 is powered on and has booted up, but an initial configuration
has not yet been performed, the Power LED flashes green and amber. If the Power
LED is solid green, the initial configuration has already been performed. If you
did not perform an initial configuration, but the Power LED is solid green, reset
the appliance to its factory defaults. Also reset the appliance if you cannot connect
to the Initial Configuration page through your browser. The initial configuration
Web page is accessible only to an appliance that has not been configured.
You can reset the SG510 to factory defaults using the Management Console or the
CLI.
To reset the SG510 to Factory Defaults

1 Access the SG510 Management Console.
https://IP_Address:8082

Where IP_Address is the IP address of the SG510.

2 Select Maintenance>General.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 81

The SG510 Does Not Come Back Up After Rebooting
If the appliance is not coming back up after rebooting and the serial port is
connected to terminal server (terminal concentrator) try the following:

1 Open an active session on the terminal server, noting any traffic being
outputted.

2 Unplug the terminal server from the appliance.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 83

P/N 231-02833

Blue Coat SG510 Installation Guide

page 84

Appendix A: Specifications

General Specifications
Important: Any modifications to the unit, unless expressly approved by Blue
Coat, could void the user’s warranty.
Dimensions (Abmessungen)
(L x W x H)

58 cm x 44 cm x 4.4 cm
22.8 in. x 17.4 in. x 2.7 in.

Weight (Gewicht)

15 kilograms maximum
33 pounds maximum

Power Input, AC
(Stromversorgung)

100 - 240 VAC
50 - 60 Hz
6.3 - 3.0A

Processor (Prozessor)

Intel® Celeron

Memory (Speicher)

SDRAM DDR333
Up to 2GB

Hard Drives (Festplatte)

IDE SATA 1.5Gb/s

Network (Netzwerk)

Two, on-board 10/100/1000 Base-T NICs
(Network Interface Cards)
Optional cards include the 1000B-SX

MTBF

100,000 Hours

P/N 231-02833

Blue Coat SG510 Installation Guide

page 85

Environmental Specifications
Specification

Operating (Betrieb)

Non-Operating (Lagerung)

Temperature
(Betriebstemeperatur)

5°C to 35°C (41°F to 95°F)

-40°C to 70°C (-40°F to 158°F)

Relative Humidity
(non-condensing)
(Relative Luftfeuchte)

15% to 95% at 35°C (95°F)

15% to 90% at 65°C (149°F)

Maximum altitude
(Hohe)

up to 3000 meters
(up to 10,000 feet)

4.6 Km (15,000 ft)

P/N 231-02833

Blue Coat SG510 Installation Guide

page 86

Appendix B:Regulatory Statements

Any modification to this product, unless expressly approved by Blue Coat
Systems, Inc., could void the user’s authority to operate the equipment.
Do not service the proxy yourself. If you have any questions, please
contact Blue Coat.
Blue Coat Corporate
420 North Mary Avenue
Sunnyvale, CA 94085-4121
408.220.2200

General System Cautions
To ensure normal operation, follow these guidelines:
Top cover removal—Before removing the top cover, turn off the power.
Ventilation guidelines—Be Careful! Do not block any openings in the system to
avoid overheating the system.
Water caution—Be Careful! Do not get any water on the system.
System use and installation—The system is intended for use in a server room
only. It is not intended be installed in individual employee work areas.

Power Cord Cautions
Caution—This product is designed to work with power systems having a
grounded neutral. To reduce the risk of electric shock, do not plug this product
into any other type of power system. Contact a qualified electrician if you are not
sure what type of power is supplied to your building.
Caution—Not all power cords have the same current ratings. Do not use the
power cord provided with your equipment for any other products or use.
Caution—there is no power switch equipped on this device. The power cord
serves as the primary disconnect device for the system. Be sure to plug the power
cord into a grounded power outlet that is nearby the system and is readily

P/N 231-02833

Blue Coat SG510 Installation Guide

page 87

accessible. Do not connect the power cord when the power supply has been
removed from the system chassis.

Class A Digital Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance
with the instruction manual, might cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the users are required to correct the
interference at their own expense.

Advertencia Digital Clase A
Este equipo ha sido probado y se ha visto que se mantiene dentro de los límites de
un dispositivo digital Clase A según la parte 15 de las normas de la FCC. Estos
límites están designados para proveer una protección razonable contra
interferencias dañinas cuando el equipo es usado en un ambiente comercial. Este
equipo genera, usa y puede irradiar energía de radiofrecuencia; si no es instalado
y usado de acuerdo al manual de instrucciones, puede causar interferencias
perjudiciales para las comunicaciones de radio. El uso de este equipo en un área
residencial puede causar interferencia perjudicial; en este caso los usuarios
deberán corregir la interferencia cubriendo los gastos por ellos mismos.

EC Community EMC Warning
This is a Class A product. In a domestic environment, this product might cause
radio interference in which case the user might be required to take adequate
measures.

Advertencia EMC de la Comunidad EC
Este es un producto Clase A En un ambiente doméstico, este producto puede
causar interferencia de radio, en cuyo caso el usuario podría verse obligado a
tomar medidas adecuadas.

Canadian EC EMC Warning
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numerique de la class A est conforme a la norme NMB-003 du Canada.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 88

Australia/New Zealand EC EMC Warning
This is a Class A product. In a domestic environment, this product might cause
radio interference, in which case the user might be required to take adequate
measures.

Taiwan BSMI Notification

Japan VCCI EMC Notification

Battery Warning Notification
CAUTION: Danger of explosion if battery is incorrectly placed. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose of
used batteries according to the manufacturer’s instructions.
Connection to ports not defined for normal operation, according to this manual,
might result in excessive radiated emissions. The user is then responsible for all
corrective action in the event of any problem.
PRECAUCION: Peligro de explosión si la batería es colocada incorrectamente.
Substituya sólo con el con el modelo original o la recomendacion del fabricante.
Elimine las baterías usadas segun las instrucciones del fabricante.
La conexión a puertos no definidos para operación normal, de acuerdo a este
manual, puede producir emisiones excesivas de radiación. El usuario es
responsable de corregir esto en caso de cualquier problema.
ATTENTION: Il y a danger d’explosion s’il y a remplacement incorrect de la
batterie. Remplacer uniquement avec une batterie de meme type ou d’un type

P/N 231-02833

Blue Coat SG510 Installation Guide

page 89

equivalent recommande par le constructeur. Metter au rebut less batteries
usagees conformement aux instructions du fabricant.
VORSICHT! Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
Ersatz nur durch denselben oder einen vom Hersteller empfohlenen
glelchwertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

Chinese Battery Warning Notification

China CCC Notification

Lasers
Location of the laser apertures if any (Par. 6.1 3). Example: connectors for fiber
optic component.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 90

¶ Ô
´ Ë
Éè
± ¸µ Ä
È Îº ÎÐ Þ
¸ Ä
£ ³¬ ý· Ç
µ Ã
µ B
½lue
Systems¹ «
˾
µ Ä
Ã÷
È ·Í ¬
Òâ
£ ¬
· ñ
Ôò
¶ ¼
» á
Ê ¹Ó Ã
» §
É¥
Ê Ê
§ ¹Ó Ã
± ¾
Éè
± ¸µ Ä
È ¨À û
¡ £

Coat

A¼ ¶
ÊÂ
ý É
ë ±
è ¾
¸ ¯
¸ æ
¾ -¼ ì² â
£
Õâ
Щ
Ï Þ

± É
¾è
± ¸²
¿É
ÄÜ
¶ Ô
Î
Éú
ÓÐ
º ¦¸

¬
± ¾
Éè
±
Ì
¨Ö Ô
¼Ú
É
ú ú
¡ Ê
¢
Ï ß
Þ
µ Íç
É
ÈÅ
£ ¬
Ï

¸´ ïµ ½
ÁË
A¼ ¶
Êý
Âë
É è
± ¸Ï Þ
¶ ±
¨ ê
× ¼
£ ¬
· û
º ÏFCC¹ æ
Ôò
µ 1Ú5Õ Â
Ö®
Ò ªÇ ó
¡ £
¹á ©
º À
Ï íµ Ä
± £
» ¤
£ Ê
¬ ¹É è
± Ô
¸ Ú
É ÌÒ µ
» ·¾ ³Ï Â
Ê ¹Ó Ã
ʱ
Ä Ü
µ Ö
¿Ó
¹ Ð
º ¦¸ É
È Å
¡ £
¹Ó Ã
² ¢
Ä ·Ü É
øä
É ä
Ƶ
ÄÁ
Ü¿
£ ¬
Èç
¹ û
° ²× °º ÍÊ ¹Ó Ã
² ·» û
º ÏË µ
ÃÊ
÷ é
µ Ä
Ò ªÇ £
ó ¬
¨Ð Å
Ô ì³ É
ÓÐ
º ¦¸ É
ÈÅ
¡ È
£ ç
¹ û
Ô¾
ÚÓ
× ¡» ·¾ ³Ï Â
Ê ¹Ó Ã
´ Ë
É è
± ¸£ ¬
º Ü
¿É
ÄÜ
» ²á ú
û
³ ýÕ â
Ö ¸Ö É
ÈÅ
µ Ä
· Ñ
ÓÃ
ÓÉ
ÓÃ
» §
³ Ð
µ £
¡ £

Å ¹· ̲ å
EMC¾ ¸¯ æ
± ¾
Éè
± ¸Î ªA ¼ ¶
² ú
Æ·¡ £
ÔÚ
¼Ò
ÓÃ
» ·¾ ³Ï Â
£ ¬
± ¾
² Æ
ú ·¿ É
Ä Ü
µ ¼
ÖÂ
Î Þ
Ï ß
µ ç¸ É
ÈÅ
£ ¬
¿ É
ÄÒ
Ü ªÇ ó
ÓÃ
» §
² É
ÓÃ
Ê Ê
µ ±
µ Ä
´ ë
Ê©
¡ £

¼Ä
Ó ´Ã ó
Å ¹· ²Ì E
å MC¾ ¸¯ æ
± ¾
A¼ ¶
Ê ýÂ ë
É è
± ¸· û
º ϼ Ó
ÄÃ
´ ó
I CES-003Ö ®
ÒÇ
ª ó
¡ £
Cet appareil numerique de la class
A est conforme a la norme NM B-003 du Canada.

° ´Ä À
óû
Ñ /Ç
Ð ÎÂ À
÷ Å
¼ ·¹ ̲ E
å MC¾ ¯
¸ æ
± ¾
Éè
± ¸Î ªA ¼ ¶
² ú
Æ·¡ £
ÔÚ
¼Ò
ÓÃ
» ·¾ ³Ï Â
£ ¬
± ¾
² Æ
ú ·¿ É
Ä Ü
µ ¼
ÖÂ
Î Þ
Ï ß
µ ç¸ É
ÈÅ
£ ¬
¿ É
ÄÒ
Ü ªÇ ó
ÓÃ
» §
² É
ÓÃ
Ê Ê
µ ±
µ Ä
´ ë
Ê©
¡ £

P/N 231-02833

Blue Coat SG510 Installation Guide

page 91

P/N 231-02833

Blue Coat SG510 Installation Guide

page 92

P/N 231-02833

Blue Coat SG510 Installation Guide

page 93

Declaration of Conformity

Declaration of Conformity
We, Blue Coat Systems
420 North Mary Avenue
Sunnyvale, CA 94085
Declare under our sole responsibility that the products
Blue Coat Systems Model 510 Series
to which this declaration relates is in conformity with the following
standards:
EN 60950: 1999-2004
EN 55022: 1994
EN 50024: 1998
Following the provisions of the 73/23/EEC and 89/336/EEC Directives,
including the Amending Directive 93/68/EEC.
Blue Coat Systems Model 510 Series is also in conformity with the following
standard:
Directive 2002/95/EC, Restriction of Hazardous Substances (RoHS).

Sunnyvale, CA 94085
Date: July 1, 2006

420 North Mary Avenue
Sunnyvale, CA 94085-4121
USA
866.30.BCOAT Tool Free
408.220.2200 Direct
408.220.2250 Fax
www.bluecoat.com

P/N 231-02833

Tim Redjaian
Director of Engineering

Blue Coat SG510 Installation Guide

page 94

Appendix C:Apéndice C: Declaraciones
Regulatorias

Cualquier modificación hecha a este producto, excepto con aprobación explícita
de Blue Coat Systems, Inc., puede anular la autoridad del usuario para usar el
equipo.
No repare el proxy por su cuenta. Si tiene alguna pregunta, contacte a Blue Coat.
Azul Coat Corporate
420 North Mary Avenue
Sunnyvale, CA 94085-4121 \
408.220.2200

Precauciones generales del sistema
Para asegurar una operación normal, siga estas líneas directivas:
Remoción de la cubierta superior—Antes de remover la cubierta superior,
apague el equipo.
Líneas directivas sobre la ventilación—¡Tenga cuidado! Para evitar el
sobrecalentamiento del sistema, no bloquee las aberturas del sistema.
Tenga precaución con el agua—¡Tenga cuidado! No deje que el agua moje el
sistema
Uso e instalación del sistema—El sistema está diseñado para ser usado sólo en
una sala de servidores. No está diseñado para ser instalado en las áreas de trabajo
de los empleados.

Conexión del cable de alimentación
Para conectar el cable de alimentación:
1Enchufe el cable de alimentación en la conexión para el cable de alimentación.
2Mueva hacia abajo el retenedor del cable de alimentación para asegurar el cable
de alimentación.
Para más información, vea la Guía rápida de comienzo.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 95

Precaución—Este producto está diseñado para funcionar con sistemas de
alimentación con conexión a tierra. Para reducir el riesgo de electrocución, no
enchufe este producto en ningún otro tipo de sistema. Contacte un electricista
competente si no está seguro de qué tipo de alimentación es suministrado a su
edificio.
Precaución—No todos los cables de alimentación tienen la misma categorización
de corriente. No use el cable de alimentación provisto con su equipo para otros
productos u otro uso.
Precaución—este dispositivo no está equipado con una perilla de encendido. El
cable de alimentación sirve de dispositivo primario de desconexión del sistema.
Asegúrese de enchufar el cable de alimentación a un tomacorriente con conexión
a tierra que esté cerca del sistema y esté accesible. No conecte el cable de
alimentación si la fuente de alimentación ha sido removida del chasis del sistema.

Lasers
Ubicación de las aberturas láser, si existen (Párr. 6.1 3). Ejemplo: conectores para
componente de fibra óptica.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 96

Appendix D:Anhang D: Regulierende
Anweisungen

Jede Veränderung dieses Produktes, welche nicht ausdrücklich von Blue Coat
Systems, Inc genehmigt wurde, kann die Nutzungserlaubnis des Benutzers
vernichten.
Üben Sie die Bevollmächtigung nicht selbst aus. Wenn Sie Fragen haben, wenden
Sie sich bitte an Blue Coat.
Blue Coat Corporate
420 North Mary Avenue
Sunnyvale, CA 94085-4121
408.220.2200

Allgemeine Systemvorsichtsmassnahmen
Um eine normale Funktionsweise zu garantieren, befolgen Sie bitte folgende
Richtlinien:
Entfernen der oberen Abdeckung—Bevor Sie die obere Abdeckung entfernen,
schalten Sie den Strom ab.
Belüftungsrichtlinie—Seien Sie vorsichtig! Blockieren Sie keine Öffnung am
System, um eine Überhitzung des Systems zu vermeiden.
Feuchtigkeitsschutzmassnahmen—Seien Sie vorsichtig! Lassen Sie kein Wasser
in das System gelangen.
Systembenutzung und Installation—Das System ist nur für die Benutzung in
einem Serverraum ausgerichtet. Es ist nicht zur Installation an einzelnen
Arbeitsplätzen gedacht.

Anschliessen des Stromkabels
Schliessen Sie das Stromkabel wie folgt an:

1 Stecken Sie das Stromkabel in den Stromkabelanschluss.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 97

2 Drehen Sie die Stromkabelhalterung nach unten, um das Stromkabel zu
sichern.
Für weitere Informationen wenden Sie sich an die Schnellstartanweisung.
Achtung—Dieses Produkt ist zum Betrieb mit Stromsystemen, welche einen
geerdeten Nulleiter haben, ausgerichtet. Um das Risiko eines Stromschlages zu
verringern, stecken Sie das Produkt nicht in andere Stromsysteme ein.
Wenn Sie nicht sicher sind, welche Art von Strom in Ihrem Haus verwendet
wird, setzen Sie sich mit einem qualifizierten Elektriker in Verbindung.
Vorsicht—Nicht alle Stromkabel haben die gleiche Stromstärkeleistung.
Verwenden Sie das mitgelieferte Stromkabel nicht mit anderen Geräten.
Vorsicht—das Gerät hat keinen Stromschalter. Das Stromkabel dient als das
Hauptabschaltgerät. Stellen Sie sicher, dass Sie das Stromkabel in eine geerdete
Steckdose in der Nähe des Geräts stecken. Schliessen Sie das Stromkabel nicht an,
wenn das Netzteil vom Gehäuse des Systems entfernt wurde.
VORSICHT! Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
Ersatz nur durch denselben oder einen vom Hersteller empfohlenen
glelchwertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

Lasers
Lage der Laseröffnungen, falls vorhanden (Par. 6.1 3). Beispiel: Anschlüsse für
Fiber Optic Komponenten.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 98

Appendix E:Simplified Chinese Regulatory
Statements

P/N 231-02833

Blue Coat SG510 Installation Guide

page 99

P/N 231-02833

Blue Coat SG510 Installation Guide

page 100

.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 101

P/N 231-02833

Blue Coat SG510 Installation Guide

page 102

Appendix F:Traditional Chinese Regulatory
Statements

P/N 231-02833

Blue Coat SG510 Installation Guide

page 103

P/N 231-02833

Blue Coat SG510 Installation Guide

page 104

.

P/N 231-02833

Blue Coat SG510 Installation Guide

page 105

P/N 231-02833

Blue Coat SG510 Installation Guide

page 106

Index

A 38
AC power cord, see power cord
automatic exit warning 23

release button for lever 14, 72
removing 14
disk-drive LEDs 17, 74
DNS server, setting and changing 25

B

E

back panel of SG510 9
bridge, configuring 40
buttons, see control buttons 21

edit mode 23
ethernet cables
attaching to the SG510 16

C

F

cable management for the SG510 11
cards, see option cards 75
certificate
invalid if SG510 moves or changes IP
address 80
CLI
logging on to using a direct serial
connection 53
logging on to using an SSH client 64–66
configuration mode 22
configuring the SG510
configuring network settings 25–46
from a remote location 55–61
using a serial terminal or PC 39–46, 47–53
using a Web browser 29–37
using front panel LCD and buttons 21–27
using the Setup Wizard 35
viewing modes in the LCD 22–23
connecting the SG510
into a network 28
control buttons 21

first-time configuration
from a remote location 55–60

A

D
default proxy policy
configuring 32, 58
disk drives
inserting into the SG510 13
lever on 14, 72

Index

completing the configuration 59
entering parameters 55–59
security warning dialog 31, 80
using a direct serial connection 39–53

restricting workstation access 51
using a Web browser 29–35
conditions required 29

placing the SG510 into a network
28

problems with first-time configuration page 78
forwarding host, configuring during initial
configuration 45
front panel
control buttons, LEDs and LCD 21
front panel of SG510
disk-drive LEDs 74
opening 13, 14
front panel of SG510, description of 8
front-panel PIN
configuring 67

I
IP address, setting and changing 25
IP gateway, setting and changing 25

Blue Coat SG510 Installation Guide

107

IP subnet mask, setting and changing 25

L
LCD
behavior, configuring 68
behavior, turning back on 21
cursor in 22–23
modes reflected in 22–23
LEDs
disk-drive 17, 74
power 17
LEDs, see front-panel LEDs or network LEDs
logging on
using a direct serial connection 53

M
Management Console
logging on to 62–63
modes
configuration 22
edit 23
status 22
mounting, see rack mounting

N
network
placing the SG510 in 28
network settings, configuring 25

O
on/off switch, see power switch
option cards
pass-through 75

P
password
auto-configuration of 25
CLI 64
configuring remotely 57
configuring using a serial terminal or PC
42, 50
configuring using a Web browser 31
configuring using the front panel 26
PC
using with the SG510 38–46

Index

PC, connection problems 38
power cord
power LED
description of 16
power switch 16

R
rack mounting the SG510 10

S
security
configuring a front-panel PIN 67
security warning dialog
at first-time configuration 31, 80
serial cable
connector for the SG510 16
serial port
securing with a password 43
serial port password
securing 33, 50, 58
serial terminal
using with the SG510 38–46, ??–53
setting up the SG510, see configuring the
SG510
SG510
back panel 9
cable management for 11
CLI passwords for 64
CLI username for 64
configuring 19
direct serial connection to 38–46
front panel features 8, 21
inserting disk drives 13
invalid certificate 80
logging on to 62–64
modes in 22–23
opening the front panel 13, 14
option cards for 75
package contents 8
placing into the network 28
power cord 16
power switch 16
rack mounting 10
troubleshooting 77

Blue Coat SG510 Installation Guide

108

status mode 22

T
terminal emulator 39
direct serial connection parameters 47
troubleshooting 77

U
username
CLI 64
configuring remotely 57
configuring using a serial terminal or PC
42, 50
configuring using a Web browser 31
default 25

W
warnings, automatic exit 23

Index

Blue Coat SG510 Installation Guide

109

Index

Blue Coat SG510 Installation Guide

110

Document Path: ["115-blue-coat-instruction-installation-guide.pdf"]

e-Highlighter

Click to send permalink to address bar, or right-click to copy permalink.

Un-highlight all Un-highlight selectionu Highlight selectionh